3 Waves Media (Edgepaint Ahead)

For this business card job for 3 Waves Media in Virginia Beach, I decided to do something a little different. In order to end up with the least amount of waste – I decided to trim and edge paint all of the cards first. I went to River City Graphics to have them trimmed down as their cutter is far superior to my little crooked manual one. Once they were trimmed I went right into edge painting. By edge painting first, I don’t ruin perfectly good prints (the over-sprayed cards can be used for line up and ink adjustment), I am able to better match the edge painting to the ink (since I think adjusting the press ink is easier), and personally it just seems to speed up the job. The disadvantage is that I had to feed one by one – which on my small 7×11″ press is probably better anyway.

IMG_3493 IMG_3495 IMG_3494 IMG_3496

I did learn a few things by doing the job in this seemingly reverse order:

1. The edge painting was NOT damaged by feeding into my pins. I use compressible pins made from foam tape, but I didn’t have any issues with the edge painting rubbing off, chipping, or transferring

2. These acrylic paints dry very quickly – by the time you finish all four sides, they are ready to be gently separated. They seem to set well with no rub off or transferring.

3. More flow aid- I found when I was doing so many stacks (I kept my stacks small so I could focus on getting nice even coverage) that the acrylic when too thick would clog the nozzle over time. For a short job I could leave the paint thicker but for a longer working time I needed more flow aid than I previously thought. Think milk, not yogurt for consistency.

4. 220lb White Savoy is top notch for edge painting. I think it does better than the Lettra but the difference might be negligible or affected by other factors I’m not noticing.

IMG_3504 IMG_3505 IMG_3501 IMG_3502

Whenever I’m printing I carefully work to try and get one perfect print – I then keep that print and my swatch or pantone guide on the delivery board so I can cross check each print that I pull from the press. It’s slower going, and I run the press as slowly as the motor will go, but I’m better able to keep track on the prints and notice if things change (like ink gets too thin or there is a blank spot). With this job I printed the logo first, which took more ink. I had to darken the ink so that the lighter coverage of ink on the text would be a good color match for the logo on the front. I think this issue is one of the secret skills of letterpress – you can use the exact same ink and get a huge range of tints based on how much is on press and how much is laying on your plates. I find I need to adjust the color in those cases where just ‘adding more ink’ isn’t an option ( when it will cause the plate to fill in or be over inked).

IMG_3507 IMG_3508 IMG_3510 IMG_3511 IMG_3512

Advertisements

3 thoughts on “3 Waves Media (Edgepaint Ahead)

  1. Savoy is totally my favorite paper right now. It doesn’t fuzz or flake like Lettra can, so it’s got a nice, crisp edge for painting.

  2. Sarah says:

    Hi! Can you tell me s bit more about what you found better with the white savoy compared to lettra? I’ve been using only lettra paper and am planning to do edge pairing on the 220. (I read your other post and purchased each item you listed! I’m studying your method!!)

    Much Ppreciated. Your blog posts are super helpful!

    • It just seems to cut better. The difference is somewhat subtle but the edge tends to be a little bit cleaner because the paper itself is firmer than lettra. For this same reason I think it prints slightly better too.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: